Code Update


It would be a huge pain to have written instructions for this. A lot of the time consuming work is actually adjusting it and getting it all to sit right, which is what these videos really help with. I tried to keep them brief enough while covering everything and break them up so you could watch the necessary parts. If there are any issues, just let me know. I'll update the videos based on feedback from any installation you want to share. 

If you have questions or want to discuss join us in the Pinside thread: https://pinside.com/pinball/forum/topic/jjpotc-treasure-chest-open-and-close

If you want to ordering the lighting mod seperately and already have the chest mod you can choose that option from the chest ordering page: https://magicalproductions.miiduu.com/jpinballs-actuated-chest-mod-jersey-jack-pinball-pirates-of-the-caribbean

*8/17/2019  - Code v1.1 is released with some fixes and updates: https://pinballmods.co/chest-mod-code-update

0. Overview

In general here are the steps you're going to take to install this mod. 

1. Remove existing lid 
2. Replace old lid plate with new one
3. Run lighting wiring (optional) & reinstall lid 
4. Install bracket under playfield
5. Run connection rod & attach to servo
6. Adjust, adjust and adjust 

0a. Notes

1. You will need to bend the rod. You'll need to put a few kinks in it to make it slide down the slot in the playfield and then back to the servo. Putting a small bend at the top of the rod first so it has enough play to open and close the chest fully is also recommended. Watch the video. The rod is easily bent. 
2. The servo should be powered on at least once before installing the rod and then turned off. When you cut the power it is easiest to do it with the forks down/switch depressed/chest closed position. That way when you are installing the rod you can tape the lid closed with some blue painters tape and be able to pull the rod down snug and tighten the quick connect bushing. 
3. You'll need to loosen and adjust the servo arm to point the brass bushing "down" towards the ground (when the playfield is raised) or at the 6 o'clock position looking at the servo with the playfield raised
4. The thumb nuts we included as a little bonus won't work on the chest. They are just a bit too wide for the chest to fully open. Sorry! 

1. Parts Introduction

2. Under Playfield Installation

3. Lighting Wiring Installation (Optional with Lighting Mod)

Lighting controller buttons

Lighting controller buttons

4. Lid Installation & Alignment

5. Rod Install & Adjustments

**** PLEASE NOTE: This video shows the servo knuckle (4 armed black plastic piece) in the wrong position for your mod. In this video you see the arm with the brass bushing on it pointing towards the ground when the playfield is raised. This is the wrong, opposite location that it should be. In your install please place the brass piece towards the ceiling, rotating it 180 degrees from where it was. 

6. Alternate Rod Method (Optional)

It was in the prototype but didn't get produced in the final game. We all saw it, we all wanted it. Now there is a mod out that will let you add the open and close chest lid to your game. Completely plug and play installation so it can be removed at any time. Thanks to the hard work of pinsider @PinballJ we have a kit for you which provides all of the necessary parts and instructions to make this a quick and easy install. No 3D printing, no programming of an Arduino, just some screwing and attachments and you're ready to go.

The kit includes the following items:

- PinballJ's Actuator Mounting Bracket with Controller, Servo and Switch
- Black lid hinge & lid bracket
- Flexible connecting rod
- Plug and play power harness
- All hardware needed 
- Zip ties

*As of 10/2019 all kits come with a 3D printed lid bracket and flexible connecting rod with ball joint end. 

You will receive a fully assembled kit (ready to be plugged in and played). The Arduino will be programmed and all of the relevant parts will be soldered. A plug and play power and connection harness will also be included for quick connection.

Read more about this mod on pinside @ https://pinside.com/pinball/forum/topic/jjpotc-treasure-chest-open-and-close

pinballJ's Actuated Chest Mod

  • $145.00


Available Options


Related Products

Black Pearl Stand-up Target Illuminated Window

Black Pearl Stand-up Target Illuminated Window

Enhance your Jersey Jack Pinball - Pirates of the Caribbean game with this cool window that is ..

$65.00

Full Width Galaxy Starmap Backboard Plastic

Full Width Galaxy Starmap Backboard Plastic

Enhance your Jersey Jack Pinball - Pirates of the Caribbean game with this full-width backboard plas..

$65.00

Spinning Pop Bumpers, Barrel and Character Upgrades

Spinning Pop Bumpers, Barrel and Character Upgrades

Are you wanting to upgrade your POTC with some really cool looking pop bumper barrels? Get in on tha..

$45.00

Chest RGB LED Lighting - Any Color, Any Brightness!

Chest RGB LED Lighting - Any Color, Any Brightness!

Here is a quick little plug and play lighting mod for your JJP POTC pirate chest. This is a tiny LED..

$40.00

Maelstrom Hidden Switch Mod

Maelstrom Hidden Switch Mod

So there is a huge black box in the middle of your playfield, want that gone? Then you just need thi..

$28.00

Actuated Chest Mod Lid & Rod Upgrade

Actuated Chest Mod Lid & Rod Upgrade

If you have the original pinballJ's Actuated Chest Mod then this upgrade is an option for you. Throu..

$25.00

Tags: actuated chest, chest, jjpotc, mod, pinball, pirates, pirates of the caribbean, potc